EVOLUTION-MANAGER

Edit File: pinconf-generic.h

/* * Interface the generic pinconfig portions of the pinctrl subsystem * * Copyright (C) 2011 ST-Ericsson SA * Written on behalf of Linaro for ST-Ericsson * This interface is used in the core to keep track of pins. * * Author: Linus Walleij <linus.walleij@linaro.org> * * License terms: GNU General Public License (GPL) version 2 */ #ifndef __LINUX_PINCTRL_PINCONF_GENERIC_H #define __LINUX_PINCTRL_PINCONF_GENERIC_H /** * enum pin_config_param - possible pin configuration parameters * @PIN_CONFIG_BIAS_DISABLE: disable any pin bias on the pin, a * transition from say pull-up to pull-down implies that you disable * pull-up in the process, this setting disables all biasing. * @PIN_CONFIG_BIAS_HIGH_IMPEDANCE: the pin will be set to a high impedance * mode, also know as "third-state" (tristate) or "high-Z" or "floating". * On output pins this effectively disconnects the pin, which is useful * if for example some other pin is going to drive the signal connected * to it for a while. Pins used for input are usually always high * impedance. * @PIN_CONFIG_BIAS_PULL_UP: the pin will be pulled up (usually with high * impedance to VDD). If the argument is != 0 pull-up is enabled, * if it is 0, pull-up is disabled. * @PIN_CONFIG_BIAS_PULL_DOWN: the pin will be pulled down (usually with high * impedance to GROUND). If the argument is != 0 pull-down is enabled, * if it is 0, pull-down is disabled. * @PIN_CONFIG_DRIVE_PUSH_PULL: the pin will be driven actively high and * low, this is the most typical case and is typically achieved with two * active transistors on the output. Setting this config will enable * push-pull mode, the argument is ignored. * @PIN_CONFIG_DRIVE_OPEN_DRAIN: the pin will be driven with open drain (open * collector) which means it is usually wired with other output ports * which are then pulled up with an external resistor. Setting this * config will enable open drain mode, the argument is ignored. * @PIN_CONFIG_DRIVE_OPEN_SOURCE: the pin will be driven with open source * (open emitter). Setting this config will enable open drain mode, the * argument is ignored. * @PIN_CONFIG_DRIVE_STRENGTH: the pin will sink or source at most the current * passed as argument. The argument is in mA. * @PIN_CONFIG_INPUT_SCHMITT_ENABLE: control schmitt-trigger mode on the pin. * If the argument != 0, schmitt-trigger mode is enabled. If it's 0, * schmitt-trigger mode is disabled. * @PIN_CONFIG_INPUT_SCHMITT: this will configure an input pin to run in * schmitt-trigger mode. If the schmitt-trigger has adjustable hysteresis, * the threshold value is given on a custom format as argument when * setting pins to this mode. * @PIN_CONFIG_INPUT_DEBOUNCE: this will configure the pin to debounce mode, * which means it will wait for signals to settle when reading inputs. The * argument gives the debounce time on a custom format. Setting the * argument to zero turns debouncing off. * @PIN_CONFIG_POWER_SOURCE: if the pin can select between different power * supplies, the argument to this parameter (on a custom format) tells * the driver which alternative power source to use. * @PIN_CONFIG_SLEW_RATE: if the pin can select slew rate, the argument to * this parameter (on a custom format) tells the driver which alternative * slew rate to use. * @PIN_CONFIG_LOW_POWER_MODE: this will configure the pin for low power * operation, if several modes of operation are supported these can be * passed in the argument on a custom form, else just use argument 1 * to indicate low power mode, argument 0 turns low power mode off. * @PIN_CONFIG_OUTPUT: this will configure the pin in output, use argument * 1 to indicate high level, argument 0 to indicate low level. * @PIN_CONFIG_END: this is the last enumerator for pin configurations, if * you need to pass in custom configurations to the pin controller, use * PIN_CONFIG_END+1 as the base offset. */ enum pin_config_param { PIN_CONFIG_BIAS_DISABLE, PIN_CONFIG_BIAS_HIGH_IMPEDANCE, PIN_CONFIG_BIAS_PULL_UP, PIN_CONFIG_BIAS_PULL_DOWN, PIN_CONFIG_DRIVE_PUSH_PULL, PIN_CONFIG_DRIVE_OPEN_DRAIN, PIN_CONFIG_DRIVE_OPEN_SOURCE, PIN_CONFIG_DRIVE_STRENGTH, PIN_CONFIG_INPUT_SCHMITT_ENABLE, PIN_CONFIG_INPUT_SCHMITT, PIN_CONFIG_INPUT_DEBOUNCE, PIN_CONFIG_POWER_SOURCE, PIN_CONFIG_SLEW_RATE, PIN_CONFIG_LOW_POWER_MODE, PIN_CONFIG_OUTPUT, PIN_CONFIG_END = 0x7FFF, }; /* * Helpful configuration macro to be used in tables etc. */ #define PIN_CONF_PACKED(p, a) ((a << 16) | ((unsigned long) p & 0xffffUL)) /* * The following inlines stuffs a configuration parameter and data value * into and out of an unsigned long argument, as used by the generic pin config * system. We put the parameter in the lower 16 bits and the argument in the * upper 16 bits. */ static inline enum pin_config_param pinconf_to_config_param(unsigned long config) { return (enum pin_config_param) (config & 0xffffUL); } static inline u16 pinconf_to_config_argument(unsigned long config) { return (enum pin_config_param) ((config >> 16) & 0xffffUL); } static inline unsigned long pinconf_to_config_packed(enum pin_config_param param, u16 argument) { return PIN_CONF_PACKED(param, argument); } #ifdef CONFIG_GENERIC_PINCONF #endif /* CONFIG_GENERIC_PINCONF */ #endif /* __LINUX_PINCTRL_PINCONF_GENERIC_H */