EVOLUTION-MANAGER

Edit File: cmtt8.mf

% THIS IS THE OFFICIAL COMPUTER MODERN SOURCE FILE cmtt8.mf BY D E KNUTH. % IT MUST NOT BE MODIFIED IN ANY WAY UNLESS THE FILE NAME IS CHANGED! % Computer Modern Typewriter Text for use with 8 point if unknown cmbase: input cmbase fi font_identifier:="CMTT"; font_size 8pt#; u#:=17/36pt#; % unit width width_adj#:=0pt#; % width adjustment for certain characters serif_fit#:=0pt#; % extra sidebar near lowercase serifs cap_serif_fit#:=0pt#; % extra sidebar near uppercase serifs letter_fit#:=0pt#; % extra space added to all sidebars body_height#:=200/36pt#; % height of tallest characters asc_height#:=176/36pt#; % height of lowercase ascenders cap_height#:=176/36pt#; % height of caps fig_height#:=176/36pt#; % height of numerals x_height#:=124/36pt#; % height of lowercase without ascenders math_axis#:=88/36pt#; % axis of symmetry for math symbols bar_height#:=63/36pt#; % height of crossbar in lowercase e comma_depth#:=40/36pt#; % depth of comma below baseline desc_depth#:=64/36pt#; % depth of lowercase descenders crisp#:=19/36pt#; % diameter of serif corners tiny#:=19/36pt#; % diameter of rounded corners fine#:=18/36pt#; % diameter of sharply rounded corners thin_join#:=18/36pt#; % width of extrafine details hair#:=22/36pt#; % lowercase hairline breadth stem#:=22/36pt#; % lowercase stem breadth curve#:=22/36pt#; % lowercase curve breadth ess#:=19/36pt#; % breadth in middle of lowercase s flare#:=28/36pt#; % diameter of bulbs or breadth of terminals dot_size#:=31/36pt#; % diameter of dots cap_hair#:=22/36pt#; % uppercase hairline breadth cap_stem#:=22/36pt#; % uppercase stem breadth cap_curve#:=22/36pt#; % uppercase curve breadth cap_ess#:=22/36pt#; % breadth in middle of uppercase s rule_thickness#:=22/36pt#; % thickness of lines in math symbols dish#:=0pt#; % amount erased at top or bottom of serifs bracket#:=0pt#; % vertical distance from serif base to tangent jut#:=27/36pt#; % protrusion of lowercase serifs cap_jut#:=27/36pt#; % protrusion of uppercase serifs beak_jut#:=0pt#; % horizontal protrusion of beak serifs beak#:=27/36pt#; % vertical protrusion of beak serifs vair#:=19/36pt#; % vertical diameter of hairlines notch_cut#:=22/36pt#; % maximum breadth above or below notches bar#:=19/36pt#; % lowercase bar thickness slab#:=19/36pt#; % serif and arm thickness cap_bar#:=19/36pt#; % uppercase bar thickness cap_band#:=19/36pt#; % uppercase thickness above/below lobes cap_notch_cut#:=22/36pt#; % max breadth above/below uppercase notches serif_drop#:=0pt#; % vertical drop of sloped serifs stem_corr#:=0pt#; % for small refinements of stem breadth vair_corr#:=0pt#; % for small refinements of hairline height apex_corr#:=8/36pt#; % extra width at diagonal junctions o#:=3/36pt#; % amount of overshoot for curves apex_o#:=3/36pt#; % amount of overshoot for diagonal junctions slant:=0; % tilt ratio $(\Delta x/\Delta y)$ fudge:=0.81; % factor applied to weights of heavy characters math_spread:=-1; % extra openness of math symbols superness:=1/sqrt2; % parameter for superellipses superpull:=0; % extra openness inside bowls beak_darkness:=0; % fraction of triangle inside beak serifs ligs:=0; % level of ligatures to be included square_dots:=false; % should dots be square? hefty:=true; % should we try hard not to be overweight? serifs:=true; % should serifs and bulbs be attached? monospace:=true; % should all characters have the same width? variant_g:=false; % should an italic-style g be used? low_asterisk:=true; % should the asterisk be centered at the axis? math_fitting:=false; % should math-mode spacing be used? generate roman % switch to the driver file