EVOLUTION-MANAGER

Edit File: cmex10.mf

% THIS IS THE OFFICIAL COMPUTER MODERN SOURCE FILE cmex10.mf BY D E KNUTH. % IT MUST NOT BE MODIFIED IN ANY WAY UNLESS THE FILE NAME IS CHANGED! % Computer Modern Math Extension 10 point if unknown cmbase: input cmbase fi font_identifier:="CMEX"; font_size 10pt#; u#:=20/36pt#; % unit width width_adj#:=0pt#; % width adjustment for certain characters serif_fit#:=0pt#; % extra sidebar near lowercase serifs cap_serif_fit#:=5/36pt#; % extra sidebar near uppercase serifs letter_fit#:=0pt#; % extra space added to all sidebars body_height#:=270/36pt#; % height of tallest characters asc_height#:=250/36pt#; % height of lowercase ascenders cap_height#:=246/36pt#; % height of caps fig_height#:=232/36pt#; % height of numerals x_height#:=155/36pt#; % height of lowercase without ascenders math_axis#:=90/36pt#; % axis of symmetry for math symbols bar_height#:=87/36pt#; % height of crossbar in lowercase e comma_depth#:=70/36pt#; % depth of comma below baseline desc_depth#:=70/36pt#; % depth of lowercase descenders crisp#:=0pt#; % diameter of serif corners tiny#:=8/36pt#; % diameter of rounded corners fine#:=7/36pt#; % diameter of sharply rounded corners thin_join#:=7/36pt#; % width of extrafine details hair#:=9/36pt#; % lowercase hairline breadth stem#:=25/36pt#; % lowercase stem breadth curve#:=30/36pt#; % lowercase curve breadth ess#:=27/36pt#; % breadth in middle of lowercase s flare#:=33/36pt#; % diameter of bulbs or breadth of terminals dot_size#:=38/36pt#; % diameter of dots cap_hair#:=11/36pt#; % uppercase hairline breadth cap_stem#:=32/36pt#; % uppercase stem breadth cap_curve#:=37/36pt#; % uppercase curve breadth cap_ess#:=35/36pt#; % breadth in middle of uppercase s rule_thickness#:=.4pt#; % thickness of lines in math symbols dish#:=1/36pt#; % amount erased at top or bottom of serifs bracket#:=20/36pt#; % vertical distance from serif base to tangent jut#:=28/36pt#; % protrusion of lowercase serifs cap_jut#:=37/36pt#; % protrusion of uppercase serifs beak_jut#:=10/36pt#; % horizontal protrusion of beak serifs beak#:=70/36pt#; % vertical protrusion of beak serifs vair#:=8/36pt#; % vertical diameter of hairlines notch_cut#:=10pt#; % maximum breadth above or below notches bar#:=11/36pt#; % lowercase bar thickness slab#:=11/36pt#; % serif and arm thickness cap_bar#:=11/36pt#; % uppercase bar thickness cap_band#:=11/36pt#; % uppercase thickness above/below lobes cap_notch_cut#:=10pt#; % max breadth above/below uppercase notches serif_drop#:=4/36pt#; % vertical drop of sloped serifs stem_corr#:=1/36pt#; % for small refinements of stem breadth vair_corr#:=1/36pt#; % for small refinements of hairline height apex_corr#:=0pt#; % extra width at diagonal junctions o#:=8/36pt#; % amount of overshoot for curves apex_o#:=8/36pt#; % amount of overshoot for diagonal junctions slant:=0; % tilt ratio $(\Delta x/\Delta y)$ fudge:=1; % factor applied to weights of heavy characters math_spread:=0; % extra openness of math symbols superness:=1/sqrt2; % parameter for superellipses superpull:=1/6; % extra openness inside bowls beak_darkness:=11/30; % fraction of triangle inside beak serifs ligs:=2; % level of ligatures to be included square_dots:=false; % should dots be square? hefty:=false; % should we try hard not to be overweight? serifs:=true; % should serifs and bulbs be attached? monospace:=false; % should all characters have the same width? variant_g:=false; % should an italic-style g be used? low_asterisk:=false; % should the asterisk be centered at the axis? math_fitting:=false; % should math-mode spacing be used? % the following font parameters are explained in {\sl The \TeX book}, Appendix G fontdimen 8: % parameters $\xi_8$ through $\xi_{13}$ will now be listed rule_thickness#, % default\_rule\_thickness 40/36pt#, % big\_op\_spacing1 60/36pt#, % big\_op\_spacing2 72/36pt#, % big\_op\_spacing3 216/36pt#, % big\_op\_spacing4 36/36pt#; % big\_op\_spacing5 generate mathex % switch to the driver file